Well since my G27 arrives tomorrow(:hyper
, I thought I would share the stuff I've been using for my 360 controller
Using only GlovePIE and PPJoy, I have emulated an H-Pattern shifter on the right analog stick, and split the left and right triggers into two axes.
First gear is activated by pushing the right analog into the top left corner, second the bottom left, etc
Neutral is used by clicking in the right thumb stick, and Reverse the B button, with the gas on the right trigger, and brake on the left.
First off, you'll need GlovePIE, and PPJoy to use it.
Add a controller on PPJoy, with 2 axes and 7 buttons, with the first axis as Analog 0, and the second Analog 1. For the buttons, button 1 should be Digital 0, button 2 Digital 1, Digital 2, Digital 3 etc.
Then open the attached .zip file, and in it should be a .PIE file. Extract and open it with GlovePIE.
At the top will be 4 lines of purple text. Take out the slashes on all four, then click run, and open lfs.
Then go to options > controls, make sure "Gear shift mode" is set to "shifter", then click the Shifter tab, and click the button (on the right side) to set reverse. Wait a few seconds and it should set it.
Then go back to GlovePIE, click stop and put the slashes back in (two for each line). Then click run and go back to lfs.
Now you can set up the rest of the controls.
Click on each of the gears in the shifter tab, and push the stick in the direction for that gear. You'll have to put it in neutral (right thumb button) before clicking another gear.
Then at the top, make sure "Throttle/Brake Axes" is set to "Separate" and click "Axes/FF", then set the Throttle and Brake axes.
If your wondering what settings I use, I have the E-Brake on the left bumper, clutch on the right bumper, with the Wheel turn at 90 degrees, and Wheel turn compensation at 1.00 with Analogue steer smooth(in Misc) at 0.80.
I also don't use a dead zone for the steering, but could help someone set a dead zone up in GlovePIE
That should do it! If you need any help, feel free to post and ask
, I thought I would share the stuff I've been using for my 360 controller Using only GlovePIE and PPJoy, I have emulated an H-Pattern shifter on the right analog stick, and split the left and right triggers into two axes.
First gear is activated by pushing the right analog into the top left corner, second the bottom left, etc
Neutral is used by clicking in the right thumb stick, and Reverse the B button, with the gas on the right trigger, and brake on the left.
First off, you'll need GlovePIE, and PPJoy to use it.
Add a controller on PPJoy, with 2 axes and 7 buttons, with the first axis as Analog 0, and the second Analog 1. For the buttons, button 1 should be Digital 0, button 2 Digital 1, Digital 2, Digital 3 etc.
Then open the attached .zip file, and in it should be a .PIE file. Extract and open it with GlovePIE.
At the top will be 4 lines of purple text. Take out the slashes on all four, then click run, and open lfs.
Then go to options > controls, make sure "Gear shift mode" is set to "shifter", then click the Shifter tab, and click the button (on the right side) to set reverse. Wait a few seconds and it should set it.
Then go back to GlovePIE, click stop and put the slashes back in (two for each line). Then click run and go back to lfs.
Now you can set up the rest of the controls.
Click on each of the gears in the shifter tab, and push the stick in the direction for that gear. You'll have to put it in neutral (right thumb button) before clicking another gear.
Then at the top, make sure "Throttle/Brake Axes" is set to "Separate" and click "Axes/FF", then set the Throttle and Brake axes.
If your wondering what settings I use, I have the E-Brake on the left bumper, clutch on the right bumper, with the Wheel turn at 90 degrees, and Wheel turn compensation at 1.00 with Analogue steer smooth(in Misc) at 0.80.
I also don't use a dead zone for the steering, but could help someone set a dead zone up in GlovePIE
That should do it! If you need any help, feel free to post and ask