think you may need a roll and flare hahahaha


what offset is that?

Nah man! Just some more negative camber and it'll be flush

ET38 lol!
16x9 3-piece

I think they are quite rare as i can't seem to find them that much is those sizes and colour!

http://img10.imageshack.us/img ... /vancouvermontreal077.jpg

alright, I drove this across canada ( Vancouver -> Montreal ) with my parents.... very fun car to drive with a great engine... im in love with it

lil too wide for the front eh?

Quote from e2mustang :

lil too wide for the front eh?

Nothing a hammer couldn't fix.

Quote from Evoluti0n_II :

Nothing a hammer couldn't fix.

A HAMMER!?!?!
Sheesh, thats a fancy way to do it.

http://www.youtube.com/watch?v=JvjQqjLa09U

Quote from Klutch :

A HAMMER!?!?!
Sheesh, thats a fancy way to do it.

http://www.youtube.com/watch?v=JvjQqjLa09U

http://www.youtube.com/watch?v=1LdDAa6TNWE&NR=1

Quote from el pibe :

http://img10.imageshack.us/img ... /vancouvermontreal077.jpg

alright, I drove this across canada ( Vancouver -> Montreal ) with my parens.... very fun car to drive with a great engine... im in love with it

how comfy was the back seat?

Quote from jibber :

http://www.youtube.com/watch?v=1lddaa6tnwe&nr=1

lol

Well duh
Beneath the fender all the rust + pipe = fail

I have a decent arch roller and heatgun in my possession

Quote from Fuse5 :

how comfy was the back seat?

even better than the trunk.....

believe me or not, i did drive! i haz pic to proove.

Oh my god... how can somebody put the numberplate THERE? Looks fugly

Looks ok on Alfas, but those are vinyl.

Quote from Töki (HUN) :

Oh my god... how can somebody put the numberplate THERE? Looks fugly

Looks ok on Alfas, but those are vinyl.

The soarer has the plate put to the side, but for a decent reason. Mainly for air flow issues to the trans cooler.

But more due to the fact that when looking side on an angle, you can't see the last two digits. Works great for speed cameras

That looks good by the way. But the Mitsu... Dunno, that position under the headlight is weird for me.

But then again, you are preventing your fmic of getting cold air on one side...
But if it isn't to bad, why not

Can't really help it.

If i have it in the middle it blocks half the IC and half the trans cooler. Been wanting to chuck it on the right side gap/intake but brothers been slack in buying longer hoseing lol

Ah ok, i see
I have some awsome update coming

take it off and put behind windshield

Quote from e2mustang :

take it off and put behind windshield

Illegal in Australia, must be attached to the front bumper in clear view. Otherwise is a $50 fine for having no front plate.

Can you not put it on the bumper under the headlight?

yes you can. but on the lancer the plate in the middle of the bumper looks kinda crap and boring.... why follow everybody else's path when you can be yourself and still reach the same destination?

Quote from e2mustang :

yep i gotta get HID's too,my car is so low and front tilts down i cant see shit even with high beams on! its cheap too,im just too lazy to work on my car

Or just get your beam adjusted by using the pitch adjuster build into the light unit. Easy work and saves you having to buy costly addons.

Quote from Klutch :

A HAMMER!?!?!
Sheesh, thats a fancy way to do it.

http://www.youtube.com/watch?v=JvjQqjLa09U

That was hardly quick. Cheap maybe.

Quote from Jakg :

Can you not put it on the bumper under the headlight?

That would require drilling through a relatively new $700 origin front bar.
...Not too keen on that.

And then cameras can see the plate perfectly, and thats no fun

Quote from Klutch :

That would require drilling through a relatively new $700 origin front bar.
...Not too keen on that.

And then cameras can see the plate perfectly, and thats no fun

It would however allow more fresh air to reach the engine bay...

I think my brother is willing to sacrifice a little performance gain over an expensive speeding ticket